Who will build the temple, from foundation to Shikhara.
MANDIR by AMR BuildTech builds temples in stone masonry, RCC frame or hybrid construction, with in-house shilpakars for stone work and structural engineering from AMR BuildTech.
Temple construction is the build phase that follows design: turning drawings into the physical temple. MANDIR by AMR BuildTech carries this out with its own team from Bhopal, Madhya Pradesh: foundation and structural work, Garbhagriha and Mandapa construction, Shikhara or Vimana construction, stone fixing and carving by in-house shilpakars, MEP installation and finishing, managed to a written schedule through to handover. Construction is done in stone masonry, an RCC frame with stone cladding, or a hybrid of the two, depending on the temple's size and design.
If you do not yet have drawings, start with our temple architecture and design service. For a full campus, see temple master planning.
Every part of the temple, built by one team from foundation to finishing.
Footings, plinth and the load-bearing frame, in stone masonry, RCC or a combination, sized for the Shikhara and campus loads above.
The sanctum walls, floor and roof, built to the dimensions and orientation fixed at design stage, ready to receive stone cladding and the idol.
The pillared hall: columns, beams, flooring and roof, in open, semi-open or enclosed form as designed.
The tower above the sanctum, built course by course in stone or cast in RCC and clad in stone, to the proportions set in design.
Dressing, fixing and carving of sandstone, marble, granite or soapstone: jalis, brackets, deity niches and ornament, by our in-house shilpakars.
Plastering, stone or marble flooring, polishing and painting, brought to a standard fit for daily worship and festival use.
Wiring, lighting, water supply, drainage and fire safety systems, installed to code and routed to stay out of sight in a sacred space.
Boundary wall, gate, parking, landscape and utilities for the temple campus.
The method is chosen at design stage to suit the temple's size, style and budget.
Load-bearing stone walls and structure, built and carved in traditional fashion. Suited to smaller and mid-sized temples where the traditional method itself is valued, with longer build time and higher stone-work skill required.
An RCC structural frame carries the loads, with stone or marble cladding and carving applied over it. Suited to larger temples and taller Shikharas, giving faster construction and predictable structural performance while keeping the traditional appearance.
RCC for the frame and services, stone masonry for the sanctum walls or specific elements. Chosen when part of the temple calls for traditional masonry and part calls for the speed and spans of RCC.
From handover of drawings to handover for consecration, in ten steps.
Approved drawings, specifications and the structural design are handed to the site team.
Site office, material storage, water and power connections and safety measures are set up.
Excavation, footings and plinth are cast and cured before any wall or column work begins.
Columns, beams and walls are built in RCC or load-bearing masonry as designed.
Sanctum and hall walls, floor slabs and roof are completed.
The tower is built in stages, course by course, checked for level and alignment at each stage.
Cladding stone is fixed and shilpakars carve jalis, brackets, niches and ornament in place or off-site.
Electrical, plumbing, lighting and fire safety systems are installed and tested.
Flooring, plastering, polishing and painting bring the temple to completion.
A final inspection is done against the drawings and specifications before handover for consecration.
| Scope item | What it covers |
|---|---|
| Foundation & structure | Excavation, footings, plinth and the RCC or masonry frame |
| Superstructure | Garbhagriha, Mandapa, Shikhara or Vimana and entrance |
| Stone work | Stone dressing, fixing and carving by in-house shilpakars |
| MEP works | Electrical, plumbing, lighting and fire safety systems |
| Finishing | Flooring, plastering, polishing and painting |
| Site works | Boundary wall, gate, parking and landscape where included |
| Project management | Site supervision, quality checks and progress reporting |
| Handover | Final inspection and handover for consecration |
What we plan for on site so the build stays safe, on schedule and true to the design.
A temple should be built to its tradition and also to the standards of a modern construction site. We manage both from the same team.
Because MANDIR is the temple vertical of AMR BuildTech, structural engineering and site management sit in the same team as the shilpakars who carve the stone.
| Material | Typical use | Why it is chosen |
|---|---|---|
| Sandstone | Load-bearing masonry, cladding, carving | Traditional to Nagara and Rajasthani-style construction, carves well. |
| Marble | Sanctum walls, flooring, idol niches | Fine finish and carving detail; fixing and jointing need experienced masons. |
| Granite | Plinths, steps, heavy-use flooring | Hard-wearing and suited to structural and high-footfall areas. |
| RCC | Foundations, structural frame, Shikhara core | Gives predictable structural performance for larger spans and taller towers. |
| Brick masonry | Infill walls, back-up masonry behind stone cladding | Economical for non-load-bearing and backing work. |
| Wood | Mandap ceilings, doors, brackets | Used for joinery and roof work where the design calls for it. |
| Lime & traditional mortars | Stone-fixing and restoration-sensitive work | Used where breathability and compatibility with old stone matter. |
| Brass and decorative metal | Kalasha, doors, bells, screens | Fixed during finishing, after stone and MEP work is complete. |
Every temple project is individually scoped based on its construction requirements. Cost depends on:
Share your approved drawings and site details for a written construction estimate. If drawings are not ready yet, start with temple architecture and design.
Concept, planning and drawings, prepared before construction begins.
Explore →Planning the full campus that this construction service then builds.
Explore →Repair, restoration and transformation of an existing temple.
Explore →Traditional stone craftsmanship carried out during construction.
Explore →Ground-up construction for Bhopal projects specifically.
Explore →The Shikhara tower, built as its own scope of work.
Explore →Marble-specific temple and home mandir construction.
Explore →Smaller mandirs built for individual homes.
Explore →Common questions about temple construction.
MANDIR by AMR BuildTech builds the temple, from foundation to Shikhara. Construction is carried out by our own team: masons, RCC crews, in-house shilpakars for stone work, and structural engineers from AMR BuildTech, coordinated by one project manager for the whole build.
Yes. Design is a separate service that produces the drawings and specifications, and this construction service builds from them. Many clients use both, but you can also bring us drawings from another architect for construction only.
Both, and hybrid construction. Stone masonry suits smaller and mid-sized temples where traditional construction itself matters. An RCC frame with stone cladding suits larger temples and taller Shikharas. The choice is made at design stage based on size, budget and timeline.
Timeline depends on size, construction method and the level of stone carving. A written schedule is provided as part of the estimate, with milestones for foundation, structure, Shikhara, stone work and finishing.
Foundation and structure, the Garbhagriha and Mandapa superstructure, Shikhara or Vimana construction, stone work and carving, electrical, plumbing and fire safety, flooring and finishing, and project management through to handover.
Yes. Structural design and site engineering are provided by the same team, so the Shikhara load, foundation and RCC frame are engineered and built by people working to the same drawings.
Concrete, steel and stone work are checked against the specification at each stage, with a final inspection against the drawings before handover. Progress and quality are reported to the trust or committee through the build.
Yes, through our temple renovation and restoration service, which covers repair, restoration and transformation of existing mandirs.
Our base is Bhopal and most projects are across Madhya Pradesh; see our city-specific pages for Indore, Ujjain, Jabalpur, Gwalior and other districts. We also take on projects from trusts elsewhere in India.
Share your drawings, site details and requirements. If you do not yet have drawings, we can start with our temple architecture and design service first.
Share your drawings, site details and timeline with our team for a written construction estimate.
MANDIR is the dedicated temple vertical of AMR BuildTech, a Bhopal construction company with over 15 years of experience. It combines temple construction with in-house design, structural engineering and stone craftsmanship, and has built 120+ temples across 28 districts of Madhya Pradesh.